CDM Gear ROC-12S Low Profile Light Mount with Built-In Sling Swivel Dock

Descripción
CDM GEAR ROC-12 SERIES LIGHT MOUNT CDM Gear ROC-12 is a new basic, made in the USA, light mount/barrel.The ROC-12 series is made from new aluminum 1-piece clamp halves that have the rail formed into the clamp. The whole unit weighs 2.4oz.It is super low profile at about a 1/2″» away from the barrel with a curved, 3 slot rail that reduces hang ups and snags. It only uses 2 bolts that correlate the 2 halves to reduce incorrect mounting. The fingers at the top of the clamp make it easy to ascertain top from bottom and allow mounting to ribbed and ported barrels. It fits within a 1.25″» space on magazine tube and includes no slip grip pads and a wrench. The ROC-12S is the same but adds a sling swivel dock built right in. These clamps fit the Remington 870 and other shotguns. The CDM Gear ROC-12R is a base barrel clamp that is used to support factory and aftermarket 1″» diameter magazine tubes, and extensions, while providing mounting rails on the left and right side for rail mountable lights and accessories.The ROC-12R uses our patented ring and curved rail design, using a flashlight ring mount to draw tight a 1″» round bodied tactical light into the curved rail portion to locate the light. This gives you the choice of using a round tac light or a rail mountable light/laser or both! All threaded holes are press formed into the mount for hardness. The entire mount is then machine finished to soften and round edges before we type III mil spec hard coat anodized for durability. Just 2 socket head cap screws work opposite each other to hold the clamp in place and are included along with a wrench and 3M no slip grip pads for the magazine tube. The tac ring can be loosened to remove the tac light without disassembly of the mount. This mount requires 1 1/2″» of mounting surface without interference from a heat shield. Will not work with heavy walled barrel or magazine tubes larger than 1″». Best on Remington 870, Mossberg 500, Winchester 1300.
Características
MATERIAL – Made from aluminum 1-piece clamp halves that have the rail formed into the clamp PROFILE – Super low profile at about a 1/2″ away from the barrel with a curved, 3 slot rail that reduces hang ups and snags EASY TO MOUNT – It only uses 2 bolts that correlate the 2 halves to reduce incorrect mounting INSTALLATION- It fits within a 1.25″ space on your magazine tube and includes no slip grip pads and a wrench FITS – Remington 870, 1100, 1187; Benelli (except SuperNova); Mossberg 500, 590; Winchester 1300, 1200 and SXP Defender
El número de Modelo (ItemModelNumber)
‎ROC-12S
Peso
4.00 Pounds
Dimensiones
5.4 x 2.8 x 1 pulgadas
Fabricante es ‎CDM Gear
Destacados
MATERIAL – Made from aluminum 1-piece clamp halves that have the rail formed into the clamp, PROFILE – Super low profile at about a 1/2″ away from the barrel with a curved, 3 slot rail that reduces hang ups and snags, EASY TO MOUNT – It only uses 2 bolts that correlate the 2 halves to reduce incorrect mounting, INSTALLATION- It fits within a 1.25″ space on your magazine tube and includes no slip grip pads and a wrench, FITS – Remington 870, 1100, 1187; Benelli (except SuperNova); Mossberg 500, 590; Winchester 1300, 1200 and SXP Defender
La calificación que le dan a CDM Gear ROC-12S Low Profile Light Mount with Built-In Sling Swivel Dock, 187 usuarios es de 4.5 sobre 5 estrellas.